20 cal decapper?
20 cal decapper?
Can any of you recommend a decapper for the 204 cases? Redding and Sinclair say they have an adaptor,lee says theirs fit all calibers.
- Joe O
- Senior Member
- Posts: 449
- Joined: Sat Jan 09, 2010 6:20 pm
- .204 Ruger Guns: Savage LRPV,Ruger K1V,G2 Contender
- Location: Upstate SC
Re: 20 cal decapper?
You can turn down the retaining cap in a universal decapping die,or buy the Sinclair adapter or others.
-
- Senior Member
- Posts: 102
- Joined: Fri Nov 23, 2012 6:51 pm
- .204 Ruger Guns: remington 700 204,cz 527 american 204
- Location: southern oregon
Re: 20 cal decapper?
Lee does not recommend the use of their universal decapping die for 17-20 cal.I use a Redding 1 N small
decapping die that works great on 20 cal without the "adapter" (17-20)rod.
decapping die that works great on 20 cal without the "adapter" (17-20)rod.
Wolves . ISIS of the animal world
- futuretrades
- Senior Member
- Posts: 835
- Joined: Sat Aug 25, 2007 11:16 am
- .204 Ruger Guns: HOWA 1500 .204 Ruger Varmint, Bull Bbl, Lupy 6-18x40 custom
Re: 20 cal decapper?
I would suggest looking into a Lee collet neck size die. This die sizes the necks of your brass for proper bullet tension, and punches the primers out in one stroke. I use it and I know a lot of other posters here use it.
NRA Benefactor Life member
HOWA 1500 Varmint 204 Ruger, Bull Barrel, Hogue Overmold Stock, Leupold VXII 6-18x40mm AO LRV Custom Reticle Timney Trigger
Cooper Mdl 21 20VarTargW/Leupold VXIII, 6-20x40AO Varmint Hunter reticle.
HOWA 1500 Varmint 204 Ruger, Bull Barrel, Hogue Overmold Stock, Leupold VXII 6-18x40mm AO LRV Custom Reticle Timney Trigger
Cooper Mdl 21 20VarTargW/Leupold VXIII, 6-20x40AO Varmint Hunter reticle.
-
- New Member
- Posts: 28
- Joined: Mon Feb 13, 2012 8:37 am
- .204 Ruger Guns: Cooper Model 21
- Location: Idaho
Re: 20 cal decapper?
I use the Universial Lee unit for my 204 and 20 VT. It is tight but it fits the 204. You just have to be a little more careful to make sure that your case is lined up with the rod.
For use in my 223 formed to 20 vt cartridges, it is nicknamed 'the donught detector'. It works fine so long as you keep the donught turned out of the inside of the shoulder/neck junction. Luckily, my K&M carbide cutting pilot fits a fired 20 vt case just about perfectly. I typicaly have to remove the donughts after fireforming, but they are not usually a problem after that.
For use in my 223 formed to 20 vt cartridges, it is nicknamed 'the donught detector'. It works fine so long as you keep the donught turned out of the inside of the shoulder/neck junction. Luckily, my K&M carbide cutting pilot fits a fired 20 vt case just about perfectly. I typicaly have to remove the donughts after fireforming, but they are not usually a problem after that.
- Tokimini
- Senior Member
- Posts: 428
- Joined: Wed Dec 08, 2010 8:21 am
- .204 Ruger Guns: Remington 700 SPS with a Shilen barrel
- Location: Victor, NY
Re: 20 cal decapper?
+ 1 on the Lee collet neck sizing die. It does a great job and comes with a very precise bullet seating die, much more consistant than the RCBS one I used to use.
Re: 20 cal decapper?
Thanks everyone for your suggestions and experience. It is great to be a member on this site.
-
- New Member
- Posts: 12
- Joined: Sat Mar 16, 2013 9:37 am
- .204 Ruger Guns: Savage model 12, 20" barrel
Re: 20 cal decapper?
I stuck my Lee decapping rod in the drill press and turned more of a taper on the main shaft so it doesn't catch on case mouths any more, works great now.